Recently Viewed Products
Heavy Duty Trailer Loading Ramp Full Kit
SKU
HD-LRMK
Contents of Master Kit :
• (Qty 4) 18" x 96" Aluminum Ramps
• (Qty 2) Adjustable Stands 18" - 24"
• (Qty 4) Aluminum Skid Seats (Trailer Adaptors) 36" Wide
• (Qty 2) Double Ramp Hanger Set for 5" Thick Ramps
• (Qty 2) Hanger for Single Ramp Stand (Holds 2 Stands)
• (Qty 2) Ramp to Load Leveler Converter Stake
• (Qty 3) Clips to Hold Lumber when using Ramp as Leveler
Availability: In stock
As low as $7,259.99
7259.99
USD
Specifications
Color | Silver |
---|---|
Material | Aluminum |
(Qty 4) 18" x 96" Aluminum Ramps
• 23,500 lb. max per axle ramps in 18″ widths
• 8 feet in length and 5 inches thick
• All ramps have pin ends for secure connection to the trailer (requires Skid Seat) and stand
(Qty 2) Adjustable Stands 18" - 24"
• Adjusts from 18″ tall to 24″ tall.
• Works with all Load Leveler ramps and may be hung beneath the trailer with optional hangers
• All ramps pin to stands for secure connection
• All stands come complete with a Base, Upper Section, all Pins, and Keepers
(Qty 4) Aluminum Skid Seats (Trailer Adaptors) 36" Wide
• Available in 36" width
• Each comes with its Locking Rod
• Welding to the trailer is preferred because of its strength, but bolting to the trailer may be used
• Aluminum Skid Seats come equipped with Rods and Standard Hitch Pins
• May be trimmed to fit around stake pockets on the upper or rear deck
• May be mounted to either or both upper and lower decks
(Qty 2) Double Ramp Hanger Set for 5" Thick Ramps
• Stores ramps beneath the trailer
• A pair of hangers required 1 left piece and 1 right piece and a pair holds 2 Ramps.
• Pair consisting of Mirror Image Complimentary Hangers for 5" Thick Ramps
• To Store 4 Ramps, 2 such sets are required
(Qty 2) Hanger for Single Ramp Stand
• These two single ramp hangers will store 2 stands
• Requires Trailer deck beams are I-Beam type, will not work with square or round tubes
• See the Installation Instructions Document for the method and list of the required hardware. Fasteners are currently not included with the set.
• Note: The Stands or their storage hangers are identical, there is no left side or right side or mirror image.
(Qty 2) Ramp to Load Leveler Converter Stake (Converts One Ramp)
• Each Converter Stake is marked "L" or "R" For Left or Right respectively and must be used in pairs of Left and Right
• Holds ramps upright for use as levelers (1 pair required per ramp, 1 left & 1 right)
• Use chain binder with up to 3/8 chain to securely fasten stakes to trailer stake pockets
• Built for standard stake pockets 3 3/8” wide
• There is a connector piece at the bottom of the Converter stake. It comes in storage mode. To be deployed, it needs to be removed, flipped, re-inserted, and locked. Then the converter stake is locked in place inside the trailer's stake pocket. To store, repeat the operation in the opposite.
• Getting the correct stakes is important. When using spacers, stake height = ramp width + spacer height used.
(Qty 3) Clips to Hold Lumber when using Ramp as Leveler
• May also be known as Dunnage holders and 3 Clips are required per Ramp
• Comes in 5″ wide which can be used for 8” and 20” wide and 5” thick ramps
• Required for use as top spacers to protect the aluminum ramp and spread the load
• Three "H" shaped Lumber Clips per pair of Converter Stakes are necessary to lock the lumber in place
Warranty Policy & Manual Instructions:
- Stand Hanger Installation Instructions.pdf
- Ramp Hanger Installation Instructions.pdf
- Warranty General Ramp.pdf