Lengthen Tarp Life by Installing New Grommets

No one needs to tell you that truck tarps are an expensive part of doing business as an owner-operator. So the longer you can continue using the same tarps, the better it is for your budget. We suggest installing new grommets when the factory-installed grommets begin to fail. This will lengthen the life of your tarps considerably.

It is fairly easy to install new grommets. All you need is a grommet kit and a little patience. Where the patience is concerned, take the time to follow all of the instructions provided by the kit manufacturer. Failing to do so will likely result in new grommets that are not as durable as the ones installed by the factory.

How to Install New Grommets

The first rule of thumb is to never replace a grommet by putting a new one into an old hole. If a grommet is failing, you are better off installing a new grommet to take its place. Having said that, look for a kit that includes multiple sized grommets plus a hole cutter and anvil. You will also need a hammer, a block of wood, and a permanent marker.

Here are the steps for installing new grommets:

1.Mark New Locations – Determine where you want to locate your new grommets, marking those locations with a permanent marker. Always install a new grommet along an outer edge at a place the material has not been compromised. Where possible, install new grommets in hem areas with extra back stitching for strength.

2.Create the Hole – The next step is to place your block of wood underneath the tarp, below the center of where the new hole will be. Then place the beveled edge of the hole-cutting tool on the tarp, at the point where you want the center of the grommet. You “cut” the hole by striking the tool once with a hammer.

3.Insert the Grommet – Insert the tall portion of the new grommet by pushing it up through the underside of the hole. Next, place a washer and the second half of the grommet on the anvil as shown in the instructions that came with your kit. Some kits also include a grommet tube that keeps everything centered.

4.Attach the Pieces – With everything in place, gently place the anvil on top of the lower half of the grommet and gently strike it with a hammer until all the pieces are tightly fit together. If your kit came with a tube, you might want to rotate it a quarter turn before every strike. This ensures a uniform fit all the way around.

That’s all there is to it. With just the few minutes of your time, you could breathe new life into your old tarps. One word of caution though – make sure you fully inspect and test your new grommets prior to using the tarp to secure a load. If any of your new grommets are not fitted together properly, they could fail on the road. That is a liability we assume you are not interested in dealing with.

Rubber Tarp Straps: Natural Rubber or Synthetic?

Every truck driver knows that you need the right tools for the job. There are different tarps for different types of loads, and different methods of fastening a tarp to the trailer bed. One of the more convenient types of straps is the rubber strap with the S-hook in either end. These straps come in both natural and synthetic, ethylene propylene diene monomer (EPDM) rubbers. The question is – is one better than the other?

Neither natural nor synthetic rubber is a better product overall. Both have their pros and cons depending on how they are used. It is best to have both kinds on hand if you are a driver that works in all regions of the country and during all seasons. Both work equally well with steel and lumber tarps of all sizes.

Natural Rubber Straps

Rubber tarp straps are incredibly convenient when all you are doing is securing the tarp itself. They go on in just seconds, and are durable enough to handle road speeds and the elements.


When you choose natural rubber, you are choosing a material that works very well in most environments, with the exception of the blazing hot sun of the American South and Southwest. High temperatures cause natural rubber to lose its elasticity, while UV rays break down the material’s composition.

On the other hand, natural rubber is the material of choice for winter use. Unlike EPDM, natural rubber does not become brittle in subfreezing temperatures. It also tends not to crack or tear in cold weather.

EPDM Rubber Straps

EPDM is an M-class synthetic rubber with a high ethylene content of between 45% and 85%. The higher the ethylene content, the more polymers can be used in the rubber mixture without affecting extrusion. This allows for a higher polymer cross-link density for stronger material.

EPDM is the best choice for securing tarps in hot weather under the scorching sun. This synthetic product holds up very well under high temperatures without losing strength or elasticity. EPDM offers a second benefit for sunny environments: it is not prone to breaking down from exposure to UV rays. Unfortunately, the same cannot be said about EPDM in cold weather environments. Cold weather tends to make EPDM brittle and prone to tearing.

Keep in mind that branding does matter when purchasing your truck tarps and straps. Where rubber straps are concerned, the fact that they all look pretty much the same can be deceiving. You are better off paying a little more for a branded product in order to get a better quality strap with a longer life and more durability.

Pairing With Rubber Ropes

You will find that it is difficult to purchase rubber straps greater than 41 inches in length. So what does the trucker do when he or she needs coverage across a much larger area? Hooking multiple tarp straps together is not necessarily a wise idea because doing so creates more opportunities for failure. Instead, pairing straps with rubber rope is the best idea.

Rubber rope can be cut to the desired length for continuous coverage across your entire load. Then insert S-hooks at either end to be attached to shorter straps where necessary. The combination of rubber rope and tarp straps provides a perfect solution for securing any load.

When buying tarp straps, it is important to have the right tool for the job. Consider weather conditions, cargo type, and any other factors necessary to choosing the right straps.

How to Clean Moldy Truck Tarps: A Perfect Step By Step Guide

Today’s modern truck tarps are made with mold resistant vinyl and poly materials that stand up pretty well to moisture and mold spores. And although winding up with a tarp covered in mold is rare, mold growth can still occur from time to time. Any mold growth on a truck tarp should be dealt with as quickly as possible in order to prevent it from spreading. Mold not only causes damage to cargo, it can also make anyone who is exposed to it sick.

Cleaning mold from a truck tarp is not difficult in principle. You can use a commercial solution purchased from the store, or you can create your own solution of baking soda and white vinegar. A good ratio is ¼-cup baking soda for every 2 cups vinegar. Regardless of the cleaning solution you choose to use, here are the steps for cleaning a moldy truck tarp:

1. Spread and Sweep

The first step is to spread your tarp out in an outdoor space large enough to let you lay it completely flat, with plenty of room to walk around. This is best done on a warm and sunny day when there is little chance of rain. You may need to weigh down the corners of the tarp if there is any breeze.

Next, use a stiff broom to sweep the tarp clean. You want to remove all of the surface dirt and loosen the mold at the same time. Be sure to sweep in the direction of the wind so that the loosened dirt and debris does not blow back onto the tarp

Heavy Duty Truck Tarp


2. Hose It Down, Scrub

Step number two is to hose down your tarp. Adjust the spray head to give yourself some pressure. This will help loosen more of a mold and any dirt and grime that did not come off with the broom. As soon as you are done hosing off the tarp, get right to work with your cleaning solution.

If you are using the baking soda and vinegar, apply the solution with a spray bottle or brush and let it sit for 15 minutes. Then take a soft bristled brush and scrub the mold spots until they come clean. You may have to add more solution as you go. If you are using a commercial cleaning solution, just follow the instructions on the bottle. When you are done scrubbing all of the spots clean, hose down the tarp for the second time.

3. Let It Dry

The last step is to let your tarp dry. If you can hang it up, it will dry more quickly while also reducing the chances that additional mold will grow. If it cannot be hung, at least use your broom to sweep off as much excess water as possible. Allowing the tarp to dry in the sun will ensure that all the water evaporates without promoting new mold growth.

When mold does form on a truck tarp, it is usually because it has folded and stored while still wet. All it takes to create mold growth is a little water and some airborne mold spores. So to avoid mold growth, do your best to allow your tarps to dry before folding and storing them. If that is not possible because of weather, pull them out and let them dry at the soonest available opportunity.

Once you are done with cleaning just inspect the tarp at fullest, if any part is weak and have patches, then just don’t waste you time and go with Mytee tarps repair kit which provides all the required things to make this kind of small repairs of truck tarps.

The Importance of Corner Protectors

In a perfect world, the American trucker could pull his or her rig into the yard, hook up a trailer in mere minutes, and be on his or her way down the road. However, we do not live in a perfect world. Truckers are responsible for securing their own loads prior to departure. When truck tarps are used, part of securing a load is putting corner protectors in place.

Corner protectors can be a nuisance for a trucker on a tight schedule. Nevertheless, they provide valuable protection in a number of different ways. Corner protectors are used to protect:

  • Fragile or sensitive cargo
  • Webbing and straps
  • Tarp material.


Truckers always have to be aware of the loads they carry and any potential risks involved. They also need to be aware of the law. For example, any load in which friction between cargo and strap could cause abrasive damage to the strap is required to be secured with corner protectors. An accident resulting from a failure to use corner protectors could result in penalties to the trucker.

Of course, truck drivers also have a responsibility to the customers they serve. A sensitive load such as drywall or decorative brick is a prime candidate for corner protectors. The last thing the driver needs is to deliver a load with damage caused by unprotected corners.

Different Types of Corner Protectors

There are different types of corner protectors corresponding to the different kinds of loads the trucker might carry. Here is a list of the ones used most often:

  • V-Boards –The most common type of corner protector is known as the V-board. This protector is nothing more than two flat surfaces joined at a 90° angle to provide cargo protection against straps. Most of the time these protectors are lightweight plastic. They offer inexpensive, easy-to-use protection for most loads.
  • Flexible Rubber – The flexible rubber corner protector is a small, rubber patch. It provides both cargo and webbing protection for loads in which 90° angles are not the norm. These are not recommended for use with chains.
  • Steel Protectors – Loads requiring the use of heavy chains need steel protectors designed with a divot or channel to keep the chain in place. There really is no substitute for this type of protector when chains are being used to secure a load.
  • Cardboard Edge Boards – Cardboard edge boards are just as popular as the plastic V-board. They are more suitable for fragile cargo and can be used to stabilize pallet loads as well. Best of all, they cost next to nothing.
  • Friction Pads – The friction pad is the ideal solution for coil loads. It lies between the coil and the tarp to reduce abrasion and stress. Friction pads can extend the life of steel tarps considerably.
  • Wear Sleeves – Your lumber tarps and cargo are not the only things needing protection. Your webbing straps also need to be taken care of with wear sleeves. Wear sleeves easily slip over the webbing to provide abrasion resistance. They are easily adjustable on the fly as well.

Corner protectors are cheap enough that the average trucker can keep plenty on hand at all times. At the same time, they provide important protection for cargo, truck tarps, straps, and chains. No trucker can do his or her job without them.